meta data for this page
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
eigenbau:analogoptocoupler [2011/08/12 12:26] – [Circuit diagram] kelkar | eigenbau:analogoptocoupler:start [2017/04/18 11:25] – ↷ Links adapted because of a move operation kmk | ||
---|---|---|---|
Line 3: | Line 3: | ||
/ | / | ||
- | ====== Precision | + | ====== Precision Optocoupler ====== |
/* Ein Titelbild: */ | /* Ein Titelbild: */ | ||
/* {{: | /* {{: | ||
==== Function ==== | ==== Function ==== | ||
- | An optocoupler is used to isolate a voltage source from the process (or experiment) by creating a optical link between the two using an LED-photodiode combination. A digital optocoupler can output only digital signals (high or low), while an analog optocoupler faithfully reproduces the input voltage into the same output voltage but now produced by an independent power source. This device provides | + | An optocoupler is used to isolate a voltage source from the process (or experiment) by creating a optical link between the two using an LED-photodiode combination. A digital optocoupler can output only digital signals (high or low), while an analog optocoupler faithfully reproduces the input voltage into the same output voltage but now produced by an independent power source. This device provides |
- | The optocoupler | + | The circuit and the board is a replica of a project |
+ | |||
+ | The original board was designed using the layout software " | ||
/* Ausführlichere Beschreibung: | /* Ausführlichere Beschreibung: | ||
- | |||
- | ==== Optionen und Alternativen ==== | ||
- | FIXME /* Wie man das Gerät sonst noch missbrauchen kann */ | ||
- | |||
- | ==== Performance ==== | ||
- | FIXME /* Wie schnell, weit, hoch das Ding auf den Bäumen ist */ | ||
==== Date ==== | ==== Date ==== | ||
Project date: August 2011 /* Die Zeit zu der das Projekt begonnen wurde */ | Project date: August 2011 /* Die Zeit zu der das Projekt begonnen wurde */ | ||
- | ==== Status ==== | + | ==== Responsible |
- | FIXME /* reine Idee / Prototyp / fertig zur Massenproduktion ... */ | + | |
- | Aufwand für Nachbau: FIXME | + | |
- | + | ||
- | ==== Developer | + | |
Hrishikesh Kelkar, kelkar@iqo.uni-hannover.de | Hrishikesh Kelkar, kelkar@iqo.uni-hannover.de | ||
- | |||
- | ==== Anwender ==== | ||
- | FIXME /* Wer das Ding bisher benutzt */ | ||
- | |||
- | ==== Working principle ==== | ||
- | FIXME | ||
==== Circuit diagram==== | ==== Circuit diagram==== | ||
* The {{: | * The {{: | ||
- | * The source files can be obtained from the [[eigenbau: | + | * The Eagle source files can be obtained from the [[eigenbau: |
- | {{: | ||
- | ==== Layout ==== | ||
- | * Abmessungen der Leiterplatte: | ||
- | * Versorgung: FIXME | ||
- | * Eingang: FIXME | ||
- | * Ausgang: FIXME | ||
- | * Anzeigen: FIXME | ||
- | * Der {{eigenbau: | ||
- | * Die {{eigenbau: | ||
- | * Die Source des Layouts im pcb-Format liegt auf der [[eigenbau: | ||
- | |||
- | /* Das Layout als gerenderter Export vom EDA-Programm | ||
- | [{{: | ||
- | */ | ||
- | |||
- | ==== Housing ==== | ||
- | FIXME /* Welche Kiste mit kurzer Begründung, | ||
- | /* | ||
- | * Die Source der Konstruktionszeichnung liegt auf der [[eigenbau: | ||
- | * Die {{eigenbau: | ||
- | */ | ||
==== Test ==== | ==== Test ==== | ||
- | FIXME /* Welche Signale | + | Eingangssignale |
- | + | ||
- | ==== Bedienung ==== | + | |
- | FIXME /* Was beim Einsatz zu beachten | + | |
- | ==== Bilder ==== | ||
- | /* Photos vom Gerät. Wenn möglich und sinnvoll Nahaufnahmen von der Platine. Die | ||
- | | ||
- | | ||
- | {{gallery> | ||
- | */ | ||
==== Kalkulation ==== | ==== Kalkulation ==== | ||
Line 84: | Line 40: | ||
| R,C | ??x | 0.02 € | 0.22 € | Bauform 0805 | | | R,C | ??x | 0.02 € | 0.22 € | Bauform 0805 | | ||
| | | | ||
- | | [[Verschnitt]] | ?.?? € ||| | | + | | [[..: |
| Summe ||| ??.?? € | | | | Summe ||| ??.?? € | | | ||