meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
eigenbau:presacler:start [2018/03/27 09:47] – [Test] meinerseigenbau:presacler:start [2018/04/11 13:47] (current) – [Status] meiners
Line 46: Line 46:
 ==== Status ==== ==== Status ====
 /* reine Idee / Prototyp / fertig zur Massenproduktion ... */ /* reine Idee / Prototyp / fertig zur Massenproduktion ... */
-prototype in testing phase\\      +prototype in testing phase\\ 
-effort for reproduction: 3 PCBs left, MC12080 needs to be ordered                  +  * general concept works, some minor modifications needed (see 'Meckerliste'
 +  * the changes are implemented in the layout (v2), in principle ready for ordering 
 + 
 +would be interesting to see if theres added phasenoise. 
 + 
 +   
 +effort for reproduction: 3 PCBs (v1) left, MC12080 needs to be ordered                  
  
 ==== Entwickler ==== ==== Entwickler ====
Line 69: Line 75:
 ==== Schaltplan ==== ==== Schaltplan ====
   * {{ :eigenbau:presacler:prescaler.pdf |schematic}} in PDF-format   * {{ :eigenbau:presacler:prescaler.pdf |schematic}} in PDF-format
-  * the source is created via KiCad and can be found on the git server: [[https://git.iqo.uni-hannover.de/vlbai/prescaler.git]]+  * the schematic and the pcb layout are created via KiCad and can be found on the git server: [[https://git.iqo.uni-hannover.de/vlbai/prescaler.git]]
  
 ==== Layout ==== ==== Layout ====
   * Size: 43 x 22 mm /* Höhe mal Breite in mm */   * Size: 43 x 22 mm /* Höhe mal Breite in mm */
   * Supply: +5V   * Supply: +5V
-  * Logic; 3x 3.3 V or 5V optional +  * Logic; 3x 3.3 V or 5V (optional) 
-  * Eingang: SMA, up to 1.1 GHz+  * Eingang: SMA, up to 1.1 GHz (nominal)
   * Ausgang: SMA $ f_{out} = f_{in} / div $ (1.1 GHz / 10 = 110 MHz max)   * Ausgang: SMA $ f_{out} = f_{in} / div $ (1.1 GHz / 10 = 110 MHz max)
-  * Der Bestückungsdruck: {{:eigenbau:presacler:start:start_layout.pdf}}+  * Der Bestückungsdruck: {{ :eigenbau:presacler:prescaler-bestueckung.pdf |}}
   * Die Bestückungsliste: {{:eigenbau:presacler:start:start__bom.pdf}}, {{:eigenbau:presacler:start:start_bom.xls}}   * Die Bestückungsliste: {{:eigenbau:presacler:start:start__bom.pdf}}, {{:eigenbau:presacler:start:start_bom.xls}}
   * {{ :eigenbau:presacler:prescaler_gerber.zip |zipped gerber files}} for PCB ordering   * {{ :eigenbau:presacler:prescaler_gerber.zip |zipped gerber files}} for PCB ordering
-  * Die Source des Layouts im pcb-Format liegt auf der [[:eigenbau:presacler:src:sourcen#start|Download-Seite des Wiki]]. FIXME  
  
 /* Das Layout als gerenderter Export vom EDA-Programm  /* Das Layout als gerenderter Export vom EDA-Programm 
Line 103: Line 108:
  
 ==== Bedienung ==== ==== Bedienung ====
-FIXME          /* Was beim Einsatz zu beachten ist. Eventuell mit Anweisung zur Inbetriebnahme. */+/* Was beim Einsatz zu beachten ist. Eventuell mit Anweisung zur Inbetriebnahme. */
  
 +there are three logic input lines, whith these the division ratio can be programmed:
 +
 +  * 3x Low: div = 80
 +  * 1x High: div = 40
 +  * 2x High: div = 20
 +  * 3x High: div = 10
 +
 +it doesn't matter which pins are high or low.
 ==== Bilder ==== ==== Bilder ====
 /* Photos vom Gerät. Wenn möglich und sinnvoll Nahaufnahmen von der Platine. Die /* Photos vom Gerät. Wenn möglich und sinnvoll Nahaufnahmen von der Platine. Die
Line 116: Line 129:
  
 ^           was ^ wieviel ^  E-Preis ^    Preis ^ Anmerkung  ^           was ^ wieviel ^  E-Preis ^    Preis ^ Anmerkung 
-|     Leiterplatte |   1x |  ??.?? € |  ~~=round(cell(1,row())*cell(2,row());2)~~ € | 1/von XXX EUR  |+|     Leiterplatte |   1x |  27.74 € |  ~~=round(cell(1,row())*cell(2,row());2)~~ € | 1/von 138.69EUR  |
 |          Gehäuse |   1x |  ??.?? € |  ~~=round(cell(1,row())*cell(2,row());2)~~ € |  | |          Gehäuse |   1x |  ??.?? € |  ~~=round(cell(1,row())*cell(2,row());2)~~ € |  |
-               * |   ?x |  ??.?? € |  ~~=round(cell(1,row())*cell(2,row());2)~~ € | ...  +         MC12080 |   1x |  04.12 € |  ~~=round(cell(1,row())*cell(2,row());2)~~ € | Mouser| 
-|              R,C |  ??x |   0.02 € |  ~~=round(cell(1,row())*cell(2,row());2)~~ € | Bauform 0805  |+|      SN74LVC3G17 |   1x |  00.50 € |  ~~=round(cell(1,row())*cell(2,row());2)~~ € | ca. Mouser| 
 +|       connectors |   1x |  ??.?? € |  ~~=round(cell(1,row())*cell(2,row());2)~~ € | ... | 
 +|              R,C |  20x |   0.02 € |  ~~=round(cell(1,row())*cell(2,row());2)~~ € | Bauform 0805  |
 |       Bestückung |                    ??.00 € ||| bei SRM  | |       Bestückung |                    ??.00 € ||| bei SRM  |
 |   [[:eigenbau:Verschnitt]] |           ?.?? € |||  | |   [[:eigenbau:Verschnitt]] |           ?.?? € |||  |
Line 127: Line 142:
 Was für die nächste Version zu tun ist: (:no:: verworfen, :Ok:: in Arbeit, :ok:: im Schaltplan, aber noch nicht im Layout, :OK:: erledigt) Was für die nächste Version zu tun ist: (:no:: verworfen, :Ok:: in Arbeit, :ok:: im Schaltplan, aber noch nicht im Layout, :OK:: erledigt)
  
-  * there seems to be a DC offset on the output. maybe a highpass on the output would be nice to get rid of it. For now I solved this issue by cutting the line between the load resistor (changed to 470 Ohm) and the removed load capacitor and soldered a 10 nF capacitor there.  +  * :OK: there seems to be a DC offset on the output. maybe a highpass on the output would be nice to get rid of it. For now I solved this issue by cutting the line between the load resistor (changed to 470 Ohm) and the removed load capacitor and soldered a 10 nF capacitor there.  
-  * the level of the logic input is not well defined, when disconnected. maybe add a pulldown.+  * :OK: the level of the logic input is not well defined, when disconnected. maybe add a pulldown.