/*********** Vorlage für Eigenbau-Seiten im ElektronIQ-Wiki. ***********/ /* Nicht gebrauchte Abschnitte bitte löschen, oder auskommentieren. */ /************************************************************-<(kmk)>***/ ====== VCO-POS ====== /* Ein Titelbild: */ /* {{:eigenbau:vco-pos:BILDNAME.jpg?300|}} */ ==== Function ==== /* Ausführlichere Beschreibung: {{:eigenbau:vco-pos:vco-pos.lyx|}} */ The device is a RF source based on the Minicicuit's POS range of voltage controlled oscillators. The output is a fixed amplitude radio frequency signal with frequency tunability over the range specified by the POS VCO. ==== Performance ==== FIXME /* Wie schnell, weit, hoch das Ding auf den Bäumen ist */ ==== Date ==== Project date: May 2011 /* Die Zeit zu der das Projekt begonnen wurde */ ==== Developer ==== Hrishikesh Kelkar, kelkar@iqo.uni-hannover.de /* Auf wessen Mist das Ding gewachsen ist. Default: Der User, der die Dokuwikiseite anlegt.*/ ==== User ==== This VCO (qty:2) is currently being used in the Magnesium experiment. ==== Operating principle ==== The circuit is based on a Minicircuits POS VCO. A stabilized voltage is provided to the POS oscillator, which creates a RF output for EOMs or AOMs. A wide range of RF frequencies can be produced by simply choosing the POS oscillator of desired frequency. ==== Circuit diagram ==== * The {{eigenbau:src:pos-vco:vco.pdf|Schematic}} in PDF-Format * The source files can be obtained from the [[eigenbau:src:sourcen#vco-pos|Download-page]] of the wiki. (Direkt-Link: {{:eigenbau:src:pos-vco:vco.sch|Schematic}}, {{:eigenbau:src:pos-vco:vco.brd|Board}}) * {{:eigenbau:vco.png? 1000|}} ==== Layout ==== * Dimensions of the PCB: 50 mm x 28.5 mm * Supply voltage: +18V * Input voltage: +18V max * The {{eigenbau:vco-pos:vco-pos_layout.pdf|Bestückungsdruck}} im PDF-Format * Die {{eigenbau:vco-pos:FIXME.zip|gezippten Gerberdaten}} für die Bestellung der Platine * Die Source des Layouts im pcb-Format liegt auf der [[eigenbau:src:sourcen#vco-pos|Download-Seite des Wiki]] /* Das Layout als gerenderter Export vom EDA-Programm [{{:eigenbau:vco-pos:vco-pos_layout.png?400|Layout (Oberseite)}}] */ ==== Housing ==== FIXME /* Welche Kiste mit kurzer Begründung, warum gerade diese */ /* * Die Source der Konstruktionszeichnung liegt auf der [[eigenbau:src:sourcen#vco-pos|Download-Seite des Wiki]]. * Die {{eigenbau:vco-pos:vco-pos_box.pdf|Konstruktionszeichnung des Gehäuses}} im PDF-Format. */ ==== Test ==== Before you solder the POS VCO, check if the voltage at the pad of pin 1 is correct. Also check if the voltage of pad 8 can be tuned using the potentiometer. Once the VCO is soldered, tune the frequency via the poti and look for the bandwidth. It should be within the specified range (e.G. POS-100: 50 - 100 MHz) ==== Photos ==== /* Photos vom Gerät. Wenn möglich und sinnvoll Nahaufnahmen von der Platine. Die Bilder sollten in einem Unterordner "bilder" zum Projekt untergebracht sein. Beipiel für den Aufruf einer Bildergalerie: {{gallery>eigenbau:vco-pos:bilder?lightbox&showname&4 }} */ ==== Price estimate ==== ^ What ^ How many ^ E-Preis (€) ^ Preis (€) ^ Note | | PCB | 1x | 4 | 4 | 60 boards for 240 € from Basista | | Housing | 1x | ??.?? | ??.?? | | | POS-x | 1x | 60 | 60 | ... | | R,C | 5x | 0.02 | 0.10 | | | Diode | 2x | 0.05 | 0.10 | | |Voltage reference | 1x | 0.50 | 0.50 | | | **Sum** ||| **64.70 €** | | /* Alternativ: Tabellen-Export aus Spreadsheet-Programm */ ==== Meckerliste ==== Was für die nächste Version zu tun ist: (:no:: verworfen, :Ok:: in Arbeit, :ok:: im Schaltplan, aber noch nicht im Layout, :OK:: erledigt) - :ok: Different voltage reference than 12 V, since you aren't able to tune the full range with only 12 V. Solution: Use 78L15 as reference. - Add a better voltage reference like REF02 or similar which is way more stable than 7815 so you get less frequency drifts.